Transition Networks

      Transition Networks - call: 727-398-5252 Cutter Networks for your best source

[Home][Adtran][Cisco][FatPipe][Fluke][Motorola][Multi-Tech][RAD][Sycamore]

Transition Networks section home Specials on Transition Networks and other LAN / WAN data communications equipment Search for Transition Networks and other LAN / WAN data communications equipment Request a quote on Transition Networks and other LAN / WAN data communications equipment

Transition Networks

SSETF1011-205 and SSETF1013-205 10/100BASE-TX to 10/100BASE-SX Media Converter

SSETF1011-205 SSETF1013-205  from Transition Networks

SSETF1011-205 and SSETF1013-205 10/100 10/100BASE-TX to 10/100BASE-SX Media Converter
Lowest possible cost solution for fiber installation up to 60 meters (100BASE-SX)
Ideal for building backbone and horizontal cabling applications where cost and 10/100 auto-negotiation are critical

Extend Network Distance using the SSETF1011-205 or  SSETF1013-205
Used in pairs, this media converter can extend distances between two twisted pair switches or a switch and a server up to 60 meters over multimode  fiber (100BASE-SX).

Connect Remote Devices
Using a single SSETF1011-205 or SSETF1013-205 10/100BASE-SX media converter, a switch with a copper port can be connected to a switch or any other 10/100BASE-SX compliant device with an existing fiber interface.

SSETF1011-205 and  SSETF1013-205 features include:
Auto-Negotiation
AutoCross™
Link Pass Through
Efficient and Reliable - The 10/100 SX Media Converter operates easily under heavy traffic loads without generating excess heat; meaning a failure-prone internal fan is unnecessary.
Automatic Link Restoration

SSETF1011-205 and SSETF1013-205 Auto-Negotiation (802.3u)
Auto-Negotiation allows devices to perform automatic configuration to achieve the best possible mode of operation over a link. Devices with this feature will broadcast their speed (10Mbps, 100Mbps, etc.) and duplex (half/full) capabilities to other devices and negotiate the best mode of operation between the two devices.

No user intervention required to determine best mode of operation
Optimal link established automatically
Quick and easy installation

While the inclusion of this feature is beneficial, the ability to disable it is equally beneficial. In the event of a non-negotiating end device trying to connect to a negotiating device, the mode of operation will drop to the least common denominator between the two devices (i.e. 100Mbps, half-duplex). Disabling this feature gives the user the ability to force the connection to the best mode of operation when trying to link with a non-negotiating device. Most Transition converters with Auto-Negotiation will allow you to disable this feature.

AutoCross™ of Transition Networks SSETF1011-205 and SSETF1013-205 10/100 10/100BASE-TX to 10/100BASE-SX Media Converter
Automatically detects and configures the twisted pair port on the converter to the correct MDI or MDI-X configuration.

Eliminates an entire category of troubleshooting
No need to identify cable type—straight-through or crossover
No user intervention required to determine correct button / switch settings

SSETF1011-205 and SSETF1013-205 Link Pass Through
Link Pass Through is a troubleshooting feature that prevents media converters from isolating link failures and it allows end devices to be notified in the event of a loss of link. Link Pass Through provides the media converter with the ability to monitor both the fiber and the copper RX ports for a loss of signal. If a loss of RX signal occurs on one media port, the converter will automatically disable the TX signal on the other port. By shutting down the fiber TX port, the link failure is “passed through” to the remote converter and device (see diagram below).

End device automatically notified of link loss
Prevents loss of valuable data unknowingly transmitted over an invalid link
Transition Networks SSETF1011-205 and SSETF1013-205 10/100 10/100BASE-TX to 10/100BASE-SX Media Converter

Automatic Link Restoration
Transition Networks's SSETF1011-205 and SSETF1013-205 converters will automatically re-establish link in all network conditions. No need to reset devices

Transition Networks's converters will automatically re-establish link when connected to switches if link was lost. With other manufacturers' converters the user must reset the converter to re-establish the link.

Auto-Negotiation Enabled

Automatic Link Restoration allows the users to continue using Auto-Negotiation with Link Loss Notification
features. With other manufacturers' converters the user must disable Auto-Negotiation and hard set the link.

Link Pass Through Activated in both directions

Automatic Link Restoration on Transition Networks's SSETF1011-205 and SSETF1013-205 allows users to continue using Link Loss Notification feature activated in both directions. Many competitive solutions allow for Link Loss Notification activation only in one direction. If Link Loss feature is activated in both directions, competitive products are put in a "deadly embrace" and they cannot restore the link without resetting the converters.

SSETF1011-205 and SSETF1013-205 application

SSETF1011-205 and SSETF1013-205 product data sheet (pdf)

 

                    Immediate price quote - Call 727-398-5252

Specials   E-mail us   Bookmark this site   More Transition Networks     Important Notices

Use Visa to purchase Data Communications Equipment    Use MasterCard to purchase Transition Networks Equipment
E-mail: Webmaster about the Transition Networks portion of this site.Transition Networks
Last modified: March 31, 2017
© 1998-2017 Cutter Networks Inc - All rights reserved