[Home][Adtran][Cisco][Eastern Research][GDC][Kentrox][Micom][Motorola][Multi-Tech][Nortel][RAD][Verlink][Visual Networks]

RAD MIC Series
Miniature Interface Converters

RAD MIC-Series 
Miniature Interface Converters

Conversion between V.24/RS-232, V.35, V.36, RS-449/422, RS-530/422 and X.21 interfaces 
Equipped with cable and connectors 
Transparent to protocol 
High speed, up to 2 Mbps (for most models) 
Immediate installation 
No AC power required (for most models) 
Compact and lightweight 

The RAD MIC Series is a family of interface converters enabling connection between the DTE and DCE with different interfaces (see Table 1). MIC models operate in synchronous applications at data rates up to 2048 kbps with balanced interface at both ends, or at data rates up to 200 kbps with V.24/RS-232 at one end. 
MICs perform both the physical conversion and the electrical conversion between the two interfaces. The circuitry is designed to provide short range interface conversion, i.e., for connection of devices which are 
co-located.
Most RAD MIC models operate without AC power, using ultra-low power from the DTE and DCE data and control signals. 
The various devices of the RAD MIC series are described in the following paragraphs. 
MIC - 24/35 
For converting between V.24/RS-232 and V.35 interfaces. MIC - 24/35 is switch-selectable and is used either for connecting a V.24/RS-232 DTE to a V.35 DCE, or for connecting a V.24 DCE to a V.35 DTE. 

MIC - 24/36 

For converting between V.24/RS-232 and V.36/RS-422 interfaces. MIC - 24/36 is switch-selectable and is used either for connecting a V.24/RS-232 DTE to a V.36/RS-422 DCE, or for connecting a V.24 DCE to a V.36 DTE. 

MIC - 232/530 

For converting between V.24/RS-232 and RS-530 interfaces. MIC - 232/530 is switch-selectable and is used either for connecting a V.24/RS-232 DTE to an RS-530 DCE, or for connecting a V.24/RS-232 DCE to an RS-530 DTE. 

MIC - 24T/21C and MIC - 21T/24C 

For converting between V.24/RS-232 and X.21 interfaces. MIC - 24T/21C is used for connecting a V.24/RS-232 DTE to an X.21 DCE. MIC - 21T/24C is used for connecting a V.24 DCE to an X.21 DTE, and has a built-in buffer to accommodate phase differences between the receive and transmit clocks of the DCE. 

MIC - 24/11 (data only) 

For converting between V.24/RS-232 and V.11/RS-422 interfaces. MIC - 24/11 is switch-selectable and is used for connecting a V.24/RS-232 DTE to a V.11/RS-422 DCE, or a V.24 DCE to a V.11 DTE. This model converts only data signals, and not control signals, and is suitable only for asynchronous applications. 

MIC - 35T/21C and MIC - 21T/35C 

For converting between V.35 and X.21 interfaces. MIC - 35T/21C is used for connecting a V.35 DTE to an X.21 DCE. MIC - 21T/35C is used for connecting a V.35 DCE to an X.21 DTE, and has a built-in buffer to accommodate phase differences between the receive and transmit clocks of the DCE. MIC - 21T/35C requires an external power supply. 

CBL-36T/21C 

For converting between RS-449/422 (V.36/V.11) and X.21 interfaces. The CBL-36T/21C cable is used for connecting a V.36 (RS-449/422) DTE to an X.21 DCE. This model is only a cable for performing cross-wiring between the two interfaces. 

CBL-530T/21C and MIC - 21T/530C 

For converting between RS-530 and X.21 interfaces. The CBL-530T/21C cable is used for connecting an RS-530/422 DTE to an X.21 DCE. This model is only a cable for performing the cross-wiring between the two interfaces. MIC - 21T/530C is used for connecting an RS-530 DCE to an X.21 DTE, and has a built-in buffer to accommodate phase differences between the receive and transmit clocks of the DCE. MIC - 21T/530C requires an external power supply. 

CBL-530/449 

For converting RS-530 to RS-449/422 (V.36/V.11) interfaces. CBL-530/449 is used for connecting an RS-530 DTE or DCE to an RS-449/422 (V.36) DCE or DTE. This model is only a cable for performing cross-wiring between the two interfaces. 

MIC - 530T/35C and MIC - 35T/530C 

For converting between RS-530 and V.35 interfaces. MIC - 530T/35C is used for connecting an RS-530 DTE to a V.35 DCE. MIC - 35T/530C is used for connecting an RS-530 DCE to a V.35 DTE. 

MIC - 35T/36C and MIC - 36T/35C 

For converting between V.35 and V.36/V.11 (RS-449/422) interfaces. MIC - 35T/36C is used for connecting a V.35 DTE to a V.36 (RS-449/422) DCE. MIC - 36T/35C is used for connecting a V.35 DCE to a V.36 DTE.

            Immediate price quote - Call 727-398-5252 or e-mail cs@bestdatasource.com

Other RAD sections of interest:

RAD Accessories, RAD  APS-8, APS-16, APS-24 Multiprotocol FRADs/PADs and Switches, RAD ATM products, RAD Baseband modems and last mile access, RAD Cables & Misc, RAD Digital Service Access Devices ( FCD ), RAD Ethernet Fiber Optic Converters, RAD Fiber Optic modems and Converters, RAD HDSL products, RAD Inverse Multiplexer, RAD IP and Ethernet Access, RAD Kilomux Data, Voice, Fax and LAN integrating Multiplexers, RAD Local Multiplexers, RAD LRS Modem rack,  RAD Media Converters, RAD Megaplex, RAD MIC - Miniature Interface Converters, RAD Medium Range Baseband Modems, RAD Modem Eliminators, RAD Remote access LAN, RAD Networks Management, RAD Optimux Fiber Multiplexers, RAD Rate and Interface Converters, RAD Sharing Devices, RAD Short Range Modems, RAD short range modem compact nest, RAD small sub-rate multiplexers, RAD Statistical Multiplexers, RAD T1/E1 Digital Cross Connects ( DACS ), RAD T1/E1 Digital Cross Connect (DACS) for single E1 / T1 applications, RAD TDMoIP, RAD Universal Interface Converter ( UCI ), RAD Voice Interface Converters, RAD Voice Trunking Gateway, RAD WEB RANger Routers

Specials   E-mail us   Bookmark this site   More RAD    Download RAD catalog (pdf 21,234kb)   Important Notices

   
E-mail: Webmaster about the RAD portion this site.
Last modified: January 16, 2008